victorianas.blogg.se - Xbox 360 jtag games

#XBOX 360 JTAG GAMES INSTALL#
#XBOX 360 JTAG GAMES PATCH#
#XBOX 360 JTAG GAMES PC#
#XBOX 360 JTAG GAMES DOWNLOAD#

Now follow the guidelines below to confirm Now open your Orig.bin file you created earlier, Upon opening the file, you shouldn't receive any bad blocks Open up another browser and google "Degraded 1BL key"Įnter the key you found in the google search results into the Degraded SettingsĬlick the Valid and set file system start to 39 Then downloaded an application call degraded from Xbins Now we need to confirm the Xbox 360 Nand Dumps you have made are valid for safekeeping.įirst off, confirm your images are identical using a hex editor to make sure they match 100%

If there are no errors read the dump again with the following command: nandpro lpt: -r16 orig2.bin.

Long time, most older Xenons are ~45Mins per nand dump, new jaspers

Wait Patiently, depending on your console revision, this could take a.

Note: FlashConfig should state FlashConfig:01198010, which means it is talking to your Xbox 360 NAND.

Run Command: nandpro lpt: -r16 orig.bin.

Run Command Prompt and route to the NANDPRO folder.

Plug in the DB25 Male plug into your PC's Parallel Port.

Plug in your Xbox 360 Console but do not power it on.

#XBOX 360 JTAG GAMES INSTALL#

make sure to install port95nt.exe from the NANDPRO folder, restart PC.

#XBOX 360 JTAG GAMES DOWNLOAD#

Download Xbins, grab NANDPRO from their FTP Server.

Once the Cable has been built, we can proceed to dumping the NAND image of your console Your NAND IMAGE using your Xbox 360 JTAG Cable :) Here's the completed and prepared Xbox 360 JTAG DB25 Male Plug with the Resistors in place.īridged.finally place the DB25 Cover on and you are ready to dump Pin Configuration on Xbox 360 JTAG DB25 Male Plug (take note of which is number 1) Mainboard below to get a better understanding of this step. Wires that need resistors soldered to the pins before them, the diagramīelow advises which ones they are, view the images of the Xbox 360 Motherboard to the pins on the DB25 Plug as per the image below) Routing them through the joiner correctly and matching the colors on the The DB25 Male Plug - Keeping in mind the color combination so we are Basically we will yet again strip oneĮnd of the RJ45 Cable, prepare the wires for solder, and then solder to Now we have completed this step, lets move Take your time as you do not want to bridge any The image below).Here's a closer look once the wires are soldered to The joiner does not need to be glued to the Xbox 360 case as it is on Idea is to have the wires soldered onto the board as per the diagramīelow, and the other end of the cable going into the RJ45 Joiner (NOTE:

#XBOX 360 JTAG GAMES PATCH#

Example: Orange on Diagram Above = Orange/White on Patch Lead.The Prepared to quickly draw up and make note of your own colorĬonfiguration. May not necessarily match the colors in the diagram below so be Of the CAT5 Patch Lead, separate the wires and prepare them for What we want to do here, is strip one end We will prepare the DB25 Male Plug First.Study the image below. 2 x Switching Diodes for later on: Part No: BAT41 or 1N4148 or 1N4153.5 x 100ohm Resistors (as per the image above).1 x DB 25 25 WAY Male Plug (LPT Printer Cable) + Hood Cover.1 x CAT5 Patch Lead (make sure it's CAT5 not CAT6).Images below of whatĬontents Required to build this JTAG XBOX 360 cable (easily found at your local electrical outlet) The Xbox 360 Console and write the new image back. Now moving on.we'll next need to createĪ simple DB-25 to RJ45 Cable to allow us to dump the NAND image from 0 or lower, let's proceed to the next step, building the NANDīUILDING LPT/RJ45 CABLE FOR YOUR XBOX 360 CONSOLE To check your Xbox 360 Dashboard Version:ġ) Turn on your Xbox 360 Console and go to Console Settings:ĭashboard is on your top right (note in the image below i have kernel Even if yourĬonsole has the right kernel version, we cannot confirm if it isĮxploitable until you dump an image of your NAND, but there is a very If you have an updated kernel, STOP RIGHT HERE andĭon't waste your time, your console is not JTAG-able. You will need an Xbox 360 Console with a Dashboard Kernel Version of.

#XBOX 360 JTAG GAMES PC#

PC with a parallel printer port required to dump/write the NAND image.

Complete step by step procedure with pictures to guide you Allowing you to run homebrew applications and backup games on your Xboxģ60 Console.